Search results

My 2001 Cherokee has one dim headlight. both highbeams work fine. both lights are new sylvainas. If this is a ground issue, where would I find the ground to fix it.

who out there has the trick to setting the timing for an '05 liberty w/3.7l. I have all the timing parts in place with the crank and idler gear marks spot on. what is left is the cam gears and bringing those marks to the 12 o'clock position. Number one is at tdc. The book isn't real talky about...

Howdy folks, I have a real puzzler for you to offer help with. The vehicle is my wifes 2001 cherokee with a 4.0I w/automatic 2-wheel drive. As the vehicle is operated, the check engine light will come on followed shortly by the check gages light and at the same time the voltmeter, sometimes all...

Folks, I need a good, sane source for a set of cylinder head bolts, 5/8 head x 7/16 thread for my soon to be out of the shop 258 engine. Anybody that can help, please do so with great speed. Thanks.

Can one of you jeepers offer info on a parts house or resaler where I can get the input and out put sensors for my '01 cherokee. 4.0L auto. Dealer seems to think they are gold plated platinum and haven't found them locally. I am in the dallas,tx. area. Thanks for your help.

Hey fellas, I'm putting in a new hcv this weekend to replace the poj that was in there. Problem, I need a hose routing pic to get this new fangled valve plumbed right. Can one of you send me a good shot of your valve and hose positions. It would save me a few new cuss words. Jeep won't help...

My '91 cherokee cruise control is misbehaving. It started surging a while back. Found some bad vacuume lines so replumbed all of them. While at it I checked vacuume on the tank and the control servo and then on the entire new plumbing and everything held good vac. Now the cruise is just nuts...

I have two high pressure lubricant delivery reels for trade. they can be replumbed to hold a boatload of air line. I would like to trade them for a viair 120 psi compressor or a 3-4000 pound bumper winch. They are shop grade, replaced by newer models.:shades:

Howdy folks, Merry Christmas. I need help removing the radio from the wifes cherokee. There are no obvious access points to pull the thing as would be found on a normal vehicle. Any advice would be great. :shades:

Yes sir. Just below and between the booster and clutch master. Can't see a bolt there like on my cj. There are two wire grouped rectangle shaped one above one below. Not in a block but an assembly 2 1/4 x 3 inches or so. Nothing in any of my books on getting it loose.

Found my bug. Need to know how to unhook wire harness from firewall. What's the trick?

I have a 91 cherokee, 5spd manual, 6cyl. here is the problem. when i start the vehicle all is good. when i use the turn signals, left or right, the vehicle immediately dies. after a few minutes i restart the vehicle and place the vehicle in reverse the vehicle dies. no other system affects this...

Any of you fellas had to fix the tilt part of your colum and the hi/lo rebound lever? My wifes 2001 needs that little cable that works the tilt and the spring that works the hi/lo lever.Any help would be great.

I have a np-228 transfer case for sale. Came out of my grand wagoneer. It was hooked to a 727 trans. Sold with the adapter and the vacuume shift motor. Good solid unit. $150.00 gets it.

Hey fellas, I am still trying to figure this clutch pilot bearing out, and now I am just befuddled. As of now I have three different cranks for the 4.0 l engine and I am no closer to putting my motor in. It seems that for the engine i built,which is an orphan(no year known), I need a collar that...

I have an ax15 as well and sometimes still have nightmares about the clutch/transmission problems. I actually went through 6, count 'em, 6 clutch kits before I found the correct clutch to mesh rite with the transmission/concentric bearing setup. In most of the kits I found the fingers of the...

i had this problem on my old gw and it turned out to be cracked wires to and from the distributor. they were shorting out enough to kill the thing but still give good voltage reads at the various points.

the engine i rebuilt is an orphan. no year known, fella i bought it from couldn't recall,even though he was a dealership.i believe to recall another tech from the same dealer said early 90,s. at this point everything has fit correctly. the hold up is this bearing.

I am trying to resolve a problem with the clutch pilot bearing. I am on the second one to try to install and this one is also too large for the hole . The size of the on listed for my cherokee is 1.055 o.d. This is too big to even get started into the hole. I sucessfully destroyed the last one,I...

Hey fellas, I'm putting a new engine in my cherokee and have run into a problem. The oil filter bracket that I put on the new motor will not accept the filter. The filter will go on the old engine bracket. I am perplexed to say the least. My wifes cherokee uses the same filter and hers is a 2001...