Search results

1068813 thanks bounty i'll give it a try tomorrow. ;-) [addsig]

1068874 Here is an update. when i went out to do this i found a really shiny vacuum nipple with nothing on it ? On the side of the intake there are three nipples, small one at the back, a fairly large one in the middle(for the egr) and a medium size one near the front about 1/4" . This is the...

1068876 I had the same problem on my yj and it turned out that one line was still leaking air. Couldn't tell by looking cause there was no fluid dripping. I knew where it was cause i didn't replace everything i was just fixing where i broke it.[addsig]

1069026 now, now guysno fighting. Does anyone have a clue where the front vacuum nipple on the intake is supposed to go? [addsig]

1064531 I believe that there is instructions in your owner's manual. if not someone on this site will have it[addsig]

1064532 my friend just called chyrsler and they said $380 canadian. We picked one up off a cherokee in the junk yard for $25. [addsig]

1064904 Do any of the people that have the modified intakes live in cold climates? How does your jeep run when it is cold and left over night?[addsig]

1064905 Should have called me about a month ago. had one sitting in my garage. Now it is at the bone yard in the back of a cherokee.[addsig]

1064906 go to an auto wrecker and find a good one in a cherokee. They are the same part as a yj. My friend just got one for $25cdn. Pretty easy to put in. :-) [addsig]

1057484 If it is making that noise when the clutch is pressed it is almost definitely the throw out bearing, it does come as one peice. but it isn't that difficult to replace just time consuming.(like everything) Mine went in my yj about two months ago and it sounded kinda like what you...

1057485 It may also be one of the wheel bearings. The easiest way to check these is while driving swerve back and forth enough to get some body roll and listen to see if it is louder turning one way than the other. Listen to which side it comes from.[addsig]

1057650 Make sure you get some oil and grease remover to wipe all of it with. I tryed to paint part of my dash without it and all the paint did was bead off. I guess it all the years of using armorall. I paint for a living and I've learned that you can't cheap out on paint, there is a reason...

1057652 welcome to the site! you'll have to let us know how the rubicon is.(in the mud) Congrats on your new jeep. I don't have to tell you that driving a jeep is a lifestyle. It is different from any vehicle you've ever drove it's like a club, so don't forget to wave. :-D [addsig]

1057657 If you're going to go through all that trouble put a 350 in it.[addsig]

1057944 normally when wheel bearings start to go they make a humming noise. You can check them by driving around 30 mph and swerve back and forth just enough to get some body roll. You'll usually only hear it coming from one side. The side with the pressure on them. Yours doesn't sound like...

1058332 Had you asked this question a month ago I would've givin you one, I sent it to the bone yard. [addsig]

1056622 Don't know where all of you live but as long as it is a jeep we wave. I've even waved at night.[addsig]

1056795 welcome to the site, don't worry after owning a jeep for while you'll be able to give lots of tips. :-D [addsig]

1056798 there is an adjustment bolt on the power steering or you would not be able to tighten the belt. I just replaced the one on my friends 89 yj with a 4.2L it's one that is right near the pulley wheel on the pump. You'll have to loosen the rest a little but you'll find it.[addsig]

1056800 what motor was in the 87 YJ? if it was a 2.5 you'll have to change the entire wiring harness, the computer and relocate the motor mounts. I just finished dropping a 4.0 liter fuel injection in my 87YJ that had a 2.5L it was a big job took almost two months off and on.[addsig]